Avolites DMX splitters will buffer, multiply, isolate and protect console DMX outputs.
The device operates from any AC mains voltage ( 85 to 265v ) with a robust 2 amp internal power supply. Standard units have DMX in, DMX loop out, Terminate On switch and LED, plus additional Power and Data LED's. Truss Splitter
The Truss splitter has three pairs. These are optically isolated from each other and can be standard 5 pin or 3 pin or 3 pin reverse. Internally, the circuit board carries spare IC's enabling you to get up-and-running again very fast in the case of an emergency.
The reliable and resilient principals of Tube Technology are utilised by Avolites in the Truss Mounting DMX splitter. Cased in a thick-wall, rigid plastic tube, the splitter is designed to attach to anything. The use of two heavy duty velcro straps means the Truss Mounting splitter needs no special clamps or other fixings. In addition to the velcro, there is a safety wire and clip.
"DMX in" and "DMX loop out" High brightness power and data LED's Standard XLR5 ( optional XLR3 or XLR3 reverse polarity ) Internal circuit board carries spare IC's Operates from any AC mains voltage from 85-265 volts "DMX in" and "DMX loop out" High brightness power and data LED's Standard XLR5 ( optional XLR3 or XLR3 reverse polarity ) Internal circuit board carries spare IC's Operates from any AC mains voltage from 85-265 volts
Allows combined wired/radio systems to be assembled Interfaces with most good simplex radio transmitters Audio connections transformer balanced to reduce hum and interference Presets multi-turn types for easy adjustment Robust extruded case - virtually indestructible Industry standard XLR type connectors
The AD913 allows communication between a Tecpro wired system and a simplex radio system, typically a pair or more of Walkie-talkies. It allows audio on the wired comms system to be transmitted to remote radios, and replies from these remote units to be heard by parties on the wired system circuit.
The unit provides a mic level output for connection to a transmitter and has a phone level input to accept a receiver. In addition it has arrangements to provide a push-to-talk (P.T.T.) or transmit on switching, operated by the signal lamp of outstations on the wired circuit to which the AD913 is connected. Any outstation can activate a radio transmission by depressing the signal lamp switch. The system signal lamps on other outstations will light in the normal way, and the speech on the wired circuit will be sent to the transmitter and the necessary transmit will be activated. All stations will hear incoming calls when the signal is off.
Can be used with any LED Parcan Patchable Music control Foot control
The LED-Foot 4 is another innovative LED controller designed and developed by Showtec. It offers you total control to 4 groups of LED Parcans. Due to the fact that all channels are patchable, the LED-Foot can work with any LED fixture in the market. Programming of programs is easy and simple. Once the LED Foot is patched and programmed it can be controlled easily by your feet. Scene selection, Chases selection, Function it all can be controlled by your foot. The LED-Foot 4 is the ideal solution for musicians who do not have their hands free to control their lighting.
Power supply: DC 12V- 500mA Power consumption: 20 Watt Power connector: Adapter (included) Chases: 12 with 24 steps Scenes: 24 + blackout scene Fixtures: 4 DMX-512: XLR 3 pole Dimensions: 360 x 183 x 69 mm (W x D x H)
FOAMCOAT is a non-toxic, water based coating for styrofoam and polystyrene foam, as well as other surfaces. It provides a hard, durable finish that resists chipping and cracking, yet can be sanded smooth or carved to add detailing. FOAMCOAT can be used on a wide variety of surfaces including foam, primed wood, concrete block, primed fiberglass, paper maché, muslin and many other materials. FOAMCOAT is fully compatible with all Roscopaints used either as tints or as surface coatings. FOAMCOAT is inherently flame retardant and water resistant.
Apply by brush, roller, or hopper spray gun depending on the desired finish. The thickness of the coating is determined by the application. When coating over fine details, use successive thin coats to build up a protective layer without obscuring the details. For an extra smooth finish without sanding, smooth the coated surface with a wet sponge just before the FOAMCOAT has set completely.
Excellent for use as a protective coating for all types of foam projects. Especially useful on foam scenery or props that receive physical abuse or need to last for extended tours. It can also be used as a texturing agent that is much more durable than plaster or joint compound.